DIY Candy Washing Machine Repair: Repair Tips

Italian Candy washing machines are popular among consumers due to their excellent quality-to-price ratio. Despite excellent performance and reliability, the machines sometimes break down. This always happens suddenly.

But don't worry too much; most problems can be resolved independently. Candy service center specialists are confident that many errors occur due to improper handling.

The specialists at the Kandy service center are confident that many errors occur due to improper handling. Incidentally, I recommend contacting EvroBytServis if you need truly high-quality and fast repairs for your Kandy washing machine.

Main problems

It's a good idea if the machine has a self-diagnostic function. Then the built-in controller will automatically detect the problem and display an alphanumeric code on the display.

If the display is missing, the illuminated indicators will help you understand the cause of the breakdown.

Common faults include:

• The car won't turn on.
• IN There is water in the drum.
• The water does not heat up.
• There is no water drainage or no water is collected at all.
• During the work process, an incomprehensible noise is heard noise or strong vibration.
• Electronic module failure. If this problem occurs, the machine will not work even when plugged in, programs will not be configured, and the indicators will flash erratically.

The Candy machine won't turn on.

What should be done in this case?

1. Try unplugging the power cord and plugging it back in. Now you can try turning on the power button.
2. Step 1 didn't help? Maybe the outlet isn't working? Try plugging another appliance into it.
3. The cause of the failure could be oxidation of the contacts or a burnt-out power button. This can be checked with a tester. If a problem is detected, the part is replaced with a new one.

The water is not heating up

If there's no warm or hot water during the wash cycle, the washing machine may be faulty. The self-diagnostic function will either notify the user of the E05 error code or flash the indicator 16 times every 5 seconds.

There are many reasons why a heating element fails. The most common ones are wear and tear or a thick layer of scale on the element. tene due to hard water.

How can I check its functionality and, if necessary, repair my Candy washing machine myself?

1. The back wall of the washing machine is removed.
2. At the bottom you will see the heater tail with two wires.
3. Use a multimeter to determine the device's resistance. If it's 20-30 ohms, it's working properly.
4. If the heating element is faulty, it needs to be removed. To do this, unscrew the bolt between the wires and pull the element out of the machine. The heating element may be stuck, making it difficult to remove without a rubber mallet.
5. When installing a new heating element, the hole must first be cleaned of any scale.
6. The functionality of the heating element is checked by turning on the machine in heating mode.

Another reason why water may not heat is a faulty temperature sensor. In this case, the machine displays error code 05 or flashes 5 times.

To check the device's resistance, first measure it at room temperature and then after heating the water. If the sensor is not working, the resistance will be the same.

Malfunction of other parts in the washing machine

Door malfunction

Breaking hatch locking devices indicated by the code E01 or the indicator flashing only once. The reason may be If you have any electronic issues, then it's best to seek qualified help or try repairing your Candy washing machine door yourself.

To remove the lock, you'll need to remove the hatch seal. To do this, use a screwdriver to pry up the clamp holding it in place. After removing the seal, unscrew the two screws securing the lock. Replace the part, and reassemble the car in reverse order.

Problem with the drainage system

A common cause of washing machine malfunction is blockage.

The machine is unable to drain the used water and displays the message E03 or flashes the indicator lights three times. What can I do?

1. Remove the front panel at the bottom.
2. Find the filter and, placing a low container underneath, unscrew it counterclockwise.
3. Clean and rinse under running water.
4. Filter It's attached to the tank with a hose. It should also be checked, as it often becomes clogged with various deposits. You can do this with a screwdriver, but be careful not to damage the hose.
5. Now turn the machine on to drain mode and check to see if the pump impeller is spinning. You'll see it through the filter hole—it's the part with the blades. Hair, thread, and wool often get tangled up in the impeller. If it's spinning, the pump is working. If it's spinning, but the pump is making a loud humming noise and the impeller itself is bouncing, the problem is with the impeller itself, which is jamming due to looseness. At this point, the pump will need to be replaced. The pump in a Candy washing machine is accessible through the bottom or tray, which is easily removed.

Inlet hose It also requires cleaning. To do this, it is disconnected and cleaned with a cable and brush.

It has an inlet filter, which is often found to contain sand and rust. This issue is accompanied by an E02 error message on the display or two blinking lights.

The pressure switch located under the top cover may fail.

This sensor will stop functioning if the tube attached to it becomes clogged.

After cleaning it from dirt, blow on it. If you hear a click, the device is working.

Bearing failure

If bearings are broken or worn out, the machine will make a loud humming noise during operation. To access them in a Candy washing machine, you'll need to remove the top cover and the drum. Candy machines are compact, so the components are packed tightly together.

The algorithm of actions is as follows:

1. There are hoses connected to the tank that must all be disconnected.
2. The powder receptacle is pulled out.
3. The counterweight is unscrewed.
4. The belt is removed from the drum pulley.
5. The wires are disconnected from the heating element.
6. The engine is removed along the guides. All wires leading from it are disconnected first.
7. The hatch is removed. To do this, unscrew the screws under the cuff and pry off the retaining clamp with a screwdriver.
8. The tank can be disassembled into 2 parts.
9. The pulley is removed from the drum shaft.
10. Knock the bearing out with light taps. Do not hit the shaft! A wooden block is used for this purpose.

11. The drum bearing is also knocked out.

New bearings are installed in place of the old ones using a pressure washer, nuts and a rod.

This instruction applies to machines with a split tank. Some models have one-piece tanks, which makes the process much more complicated and makes replacing the bearings at home difficult.

Candy Aquamatic error codes

Repairing a Candy Aquamatic washing machine is easier because it's equipped with a self-diagnostic system. To decipher the error code, pay attention to the left indicator. After reading the instructions and learning how many flashes are typical for a particular error code, you can repair the machine yourself.

- Code 1 This means the hatch is blocked. You should check to see if the hatch is securely closed. This code also indicates a problem with the controller.

- Code 2 The water supply to the tank is failing—either insufficient or no water at all. The cause could be the valve, controller, water faucet, or a blockage.

- Code 3 This indicates drainage problems. The pump, drain hose, filter, and siphon may be faulty.

If there's still water in the drum after the wash cycle, first shut off the water supply, remove the panel at the bottom of the machine, and drain the water using the drain pump filter. After this, you can investigate the problem. The pump is also checked.

Any washing machine repair should begin with diagnostics. Only after assessing the severity of the problem can you begin the repair yourself or contact an experienced technician.