DIY Ariston Washing Machine Repair + Video

The Hotpoint Ariston washing machine, made by an Italian manufacturer, is reliable and high-quality. However, some parts sometimes fail. How can you repair an Ariston washing machine yourself? We'll discuss this in this article.

You can, of course, take it to a service center for repairs, but to save money and with skillful hands and a smart head, you can repair an electromechanical household appliance yourself.

Repairing your Ariston washing machine yourself is easy. Follow our instructions for restoring your washing machine, and your assistant will serve you well for many years to come.

Ariston washing machine malfunctions

• In the Ariston electromechanical device, the main reason leading to incorrect operation of the machine is blockages.
• In addition, the heating element becomes unusable due to the formation of limescale deposits on the heating element due to hard water.
• Pump It can also become faulty due to long-term use.
• Sometimes the fill valve fails due to damage to the rubber seal.
• In rare cases it is necessary to change bearings and seals.
• Electronics almost never break down, but we will still touch on the issue of replacement a little control unit.

Clearing blockages during washing machine repair at home

Clearing the blockage yourself is easy. Just check the drain filter, which is located on the lower right side under the panel.

By cleaning the filter, you'll eliminate the cause of your washing machine's malfunction. A clogged drain hose is less common because it's thick.

The pump may be clogged, but this is rare because there is an additional filter in front of it.

The drain hose only gets clogged if you install it incorrectly.

Check the sewer system; it could also be clogged. Disassemble the unit, remove the hose, loosen the clamps, and flush it. Remove the pump, unscrew the fasteners, and disconnect the sensors.

DIY Ariston washing machine pump repair

To determine whether your unit's pump isn't working, the filter is malfunctioning, or the drain hose is clogged, you need to be familiar with the signs of a pump failure.

Signs of pump failure:

1. Drain the pump is humming, but the water does not drain.
2. The machine may stop while the system is operating.
3. The water flows out slowly.

Repair of the Ariston washing machine pump should be carried out as follows:

• Turn off the power to the washing machine and drain the water completely, lowering the hose to the floor, while placing rags to absorb the liquid;
• The pump can be accessed through the bottom, as in this brand's models it is located at the bottom of the washing machine. To remove the pump, turn the machine on its side and remove the bottom panel.
• disconnect the wires going to the drain pump, loosen the clamps and remove the pump;
• Now you need to disassemble it. To do this, use a Phillips-head screwdriver to unscrew the screws on the pump housing. Some Ariston washing machine models use clamps, rather than screws, to secure the pump. Lightly press on the pump housing while turning it counterclockwise. It will unscrew.
• Use a marker to mark the motor's position in the volute so you can reassemble it correctly later. Remove the motor and impeller. The impeller in the pump should rotate in bursts, not slowly and smoothly, because it contains a magnet rotating in a coil. This magnet ensures interaction between the rotor and the stator of the washing machine.
• If there is no visible debris, but the impeller still does not rotate, then continue disassembling the pump. The motor housing has latches that need to be pressed slightly with a screwdriver to remove it from the spool. Once the motor is removed from the housing, you'll see a single piece—the crosspiece. Using a heat gun, be sure to wear gloves, heat the tailpiece (the long part) on low power.
• Use a screwdriver to pry the crosspiece out of the housing along with the magnet. There's a lot of debris on the magnet and in the housing from which the part was removed. The parts need to be thoroughly cleaned or rinsed.
• Next, remove the magnet from the shaft. You'll see the bearing, which you should clean and lubricate.
• Begin assembling the pump. When reassembling, make sure the O-ring under the blades is firmly seated. When assembling the parts, press them gently until they click into place.
• Sometimes bearings not only become clogged, but also fail. Faulty bearings cause the impeller to wobble, causing it to rub against the volute housing. You'll hear noise and a humming sound from the pump, but no water will be dispensed. The washing machine may even stop working. Purchase replacement bearings from a service center or other Russian cities, or from specialized stores. If the seals are faulty, replace them as well.
• Reassemble the pump in reverse order, then the entire washing machine. Repairing Ariston washing machine problems

When a Hotpoint Ariston malfunctions, it displays an error on the screen. It's important to know the error codes to determine the fault and the cause of the breakdown.

The fill valve is broken

If the inlet valve in the Ariston is broken, water will constantly flow into the washing machine, even when it is not working and is disconnected from the power supply.

To check the fill valve, unscrew the fasteners and remove the top cover. The valve is located where the drain hose connects to the electromechanical unit housing.

Check the gaskets first. If they have not lost their functionality, measure the valve resistance. Place the probes on the contacts of the filler valve and check whether the resistance is optimal (from 30 to 50 Ohms).

If it's lower or higher than expected, it means the water inlet valve isn't working. To replace it, unscrew the old valve from the housing and screw in the new one. Be sure to connect the sensors.

The heating element is faulty

If the heating element is faulty, it must be replaced. A malfunction is indicated by the water not heating up or by the washing machine washing in cold water on all programs. Sometimes the machine displays an error message and stops.

To replace the heating element, you need to remove the back panel. Under the tank, there are two contacts with a fastening element in the middle. This is the heating element. Measure the resistance of the heating element with a multimeter.

If the resistance is within normal limits, then there is no need to change the heating element - it is working properly. To remove the heating element, you need to unscrew the screw in the middle and pull it towards you using a rocking motion.

Water may not heat up due to a loose connection between the wires and the heating element, which can occur due to the washing machine's strong vibrations. Water may also not heat up if the temperature sensor is faulty.

Use a tester or multimeter and check the sensor's resistance when cold and when hot. If the resistance is the same, it's broken and needs to be replaced. The resistance should be different.

Ariston washing machine drum repair

The high-quality and durable material from which the drum of household appliances is made also deteriorates because hard foreign objects get into it, which can damage the unit, forming cracks.

The plastic rib inside the drum may become deformed. To replace the drum, you need to remove it.

To remove the drum yourself, you will need the following set of tools:

1. a set of screwdrivers, especially a Phillips screwdriver and a slotted bit;
2. screwdriver;
3. pliers;
4. hammer;
5. hexagons of different sizes.

Before you begin disassembling the drum, you must disconnect the machine from the power supply, disconnect the drain hose, and turn off the water supply.

Using a Phillips screwdriver, remove the bolts from the rear, front and top walls, and then remove the panels themselves.

Remove the powder container. Use a flat-head screwdriver to remove the module. The control unit doesn't need to be completely removed, as long as it doesn't interfere with the drum removal.

Remove it hatch cuffRemove the bottom bar by unscrewing the screws. The electronics, shock absorbers, and other components must be removed from the loading tank.

Remove the drum from the unit and disassemble it. Remove the screws holding the two sides of the drum together. Use a screwdriver to pry up the seals and remove them.

Bearing repair

The bearing in the drum may break and wear out. It needs to be replaced. Only purchase the correct brand bearing from a specialized store or order it from the official Ariston washing machine website. You can also purchase it from a repair shop.

Use a metal rod and a hammer to knock out the bearings. If they are faulty, replace them. If the drum is warped, replace it with a new one.

Perform reverse assembly. If the problem is with the plastic rib, there's no need to disassemble the drum. Simply remove the washing machine door. Use a metal rod with a diameter smaller than the holes in the plastic rib.

Insert the rod into one of the holes on the rib, which opens the latch and removes the plastic piece. A new plastic rib is installed in its place. Slide the plastic rib along the groove until the latch fits into the hole and closes.

Self-repair of the module

Modern Ariston machines are equipped with an electronic display. It displays a warning message about a malfunction in the washing machine.

The control panel's LED indicators receive a signal from the faulty unit. An error code appears on the display, indicating a component failure.

When a malfunction occurs in the Ariston Margarita 2000 washing machine, the power button starts flashing and the control knob rotates constantly. The flashing pattern varies depending on the fault. The codes can be found in the machine's manual.

The control unit may fail due to mechanical damage or water ingress. Control module repair You can only do it yourself if a small part has failed or if you need to replace the entire board.

In other cases, contact a service center. Professionals will help you repair and resolder complex electronic circuits.

Depending on the brand of the board, you'll need to loosen the screws on the board or remove the plates with a wrench. Remove the control unit and replace it with a new one. Carefully tighten the fasteners to avoid damaging any components.

Cost of repairing an Ariston washing machine

The cost of repairs depends on their complexity. If the unit doesn't drain, the cost of repairs ranges from 1,200 to 3,000 rubles.

Control module repair costs over 3,500 rubles. Grinding and knocking noises can be fixed at a service center in Moscow for between 3,000 and 5,000 rubles.

Today we've shared our knowledge on how to repair an Ariston washing machine yourself.

We hope you'll succeed and that doing your own repairs will be inexpensive, eliminating the need to pay for disassembling and reassembling your washing machine or having it repaired by specialists.